Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
image_modifikations [2015/10/18 14:02]
admin [Disable the Camera LED] 		image_modifikations [2016/01/28 16:45] (current)
admin [Arduino]
Line 1: Line 1:
----- +===== Embedded Artist Image Modifications for Raspbian Wheezy =====
-**Embedded Artist Image Modifications** +
-----+
  
-These modifications work with the Raspberry Pi B+, too. +These modifications work with the Raspberry Pi B and B+. 
-Download and burn the Raspbian Wheezy 2014-09-09 Image.\\ +Download and burn the Raspbian Wheezy 2014-09-09 Image:\\ 
-[[http://www.raspberrypi.org/downloads/]]+[[https://www.raspberrypi.org/downloads/raspbian/]]\\
 Boot you Rasperry Pi and log in...\\ Boot you Rasperry Pi and log in...\\
-user: Pi\\+user: pi\\
 pass: raspberry\\ pass: raspberry\\
 ... and make an update:\\ ... and make an update:\\
   $ sudo apt-get update   $ sudo apt-get update
-\\+  $ sudo apt-get upgrade
  
 ---- ----
-==== Change name and password ====+==== Name and Password ==== 
 +Change the name and the password.
 \\ \\
 [[http://raspi.tv/2012/how-to-create-a-new-user-on-raspberry-pi|How to create a new user]] [[http://raspi.tv/2012/how-to-create-a-new-user-on-raspberry-pi|How to create a new user]]
Line 36: Line 35:
   $ passwd   $ passwd
  
-The passwd command allows you to change your password, you will be prompted for your old password, then you new password twice. The password is "dernulleffekt".+The passwd command allows you to change your password, you will be prompted for your old password, then you new password twice.
  
 4. Reboot: 4. Reboot:
   $ sudo reboot   $ sudo reboot
-\\ 
  
 ---- ----
-==== Install Scrips ====+==== Script ====
 Install the Shutdown/Reset Button and the Blink Program as startup programs. Install the Shutdown/Reset Button and the Blink Program as startup programs.
  
Line 68: Line 66:
 write before exit 0: write before exit 0:
    # run reset and shutdown script    # run reset and shutdown script
-   printf "start shutdown aund reset button\n"+   printf "start shutdown aund reset button on GPIO 22\n"
    /home/pi/paper-duino-pi/shutdownbutton_02.py &    /home/pi/paper-duino-pi/shutdownbutton_02.py &
-   printf "start blinking\n"+   # start blinking 
 +   printf "start blinking on GPIO 27\n"
    /home/pi/paper-duino-pi/blink_02.py &    /home/pi/paper-duino-pi/blink_02.py &
        
Line 81: Line 80:
  
 ---- ----
-==== Install Arduino ====+==== Arduino ====
 Install the Arduino IDE and the Paper-Duino-Pi modifications. Install the Arduino IDE and the Paper-Duino-Pi modifications.
  
Line 88: Line 87:
  
 2. For the modification of the GPIO Pin and the Avrdude, the easiest way is to download the setup for the AlaMode board: 2. For the modification of the GPIO Pin and the Avrdude, the easiest way is to download the setup for the AlaMode board:
-  $ wget http://dernulleffekt.de/programme/paper-duino-pi-setup.tar.gz +  $ wget http://dernulleffekt.de/programme/paper-duino-pi-setup_02.tar.gz 
-<del>[[http://www.wyolum.com/downloads/alamode-setup.tar.gz]]</del>\\+<del>[[http://git.io/alamode-setup]]</del>\\
 unpack it, unpack it,
-  $ sudo tar xf alamode-setup.tar.gz+  $ sudo tar xf paper-duino-pi-setup.tar.gz
 and run the setup. and run the setup.
-  $ cd alamode-setup+  $ cd paper-duino-pi-setup
   $ sudo ./setup   $ sudo ./setup
 That will install a new version of the avrdude and will also do some Linux modifications (one for the alamode board). That will install a new version of the avrdude and will also do some Linux modifications (one for the alamode board).
Line 119: Line 118:
  
 ---- ----
-==== Install PD-extended ====+==== PD-extended ====
  
 1. To install pd-extended run the following command in your terminal:  1. To install pd-extended run the following command in your terminal: 
Line 154: Line 153:
  
 ---- ----
-==== Enable Sound on Jack ====+==== Sound on Jack ==== 
 +Enable the Sound on Jack.
   $ sudo modprobe snd_bcm2835   $ sudo modprobe snd_bcm2835
   $ sudo amixer cset numid=3 1   $ sudo amixer cset numid=3 1
  
 +or change in
 +  $ sudo raspi-config
 +Advanced Options/Audio
 ---- ----
 ==== Stop blanking ==== ==== Stop blanking ====
Line 207: Line 210:
  
 ---- ----
-==== The SSH connection ====+==== SSH ====
 Set the SSH connection and the IP address. Set the SSH connection and the IP address.
    
Line 237: Line 240:
  
 ---- ----
- ==== FAT32 partition ====+ ==== FAT32 Partition ====
 With G-Part make a fat32 partition on the SD Card, named "fat32". With G-Part make a fat32 partition on the SD Card, named "fat32".
  
Line 250: Line 253:
  
 ---- ----
-==== Disable the Camera LED ====+==== Camera LED ==== 
 +Disable the Camera LED.
   $ sudo nano /boot/config.txt   $ sudo nano /boot/config.txt
 edit: edit:
   disable_camera_led=1   disable_camera_led=1
  
- +---- 
-==== Downgrade the omxplayer ====+==== Omxplayer ====
 To prevent the OMXPlayer to show the time and "pause" one have to downgrade it to version 0.2.7.\\ To prevent the OMXPlayer to show the time and "pause" one have to downgrade it to version 0.2.7.\\
   $ sudo apt-get autoremove omxplayer   $ sudo apt-get autoremove omxplayer
Line 263: Line 267:
   $ sudo dpkg -i omxplayer_0.2.7~git20130615~d87aa60a_armhf.deb   $ sudo dpkg -i omxplayer_0.2.7~git20130615~d87aa60a_armhf.deb
   $ rm omxplayer_0.2.7~git20130615~d87aa60a_armhf.deb   $ rm omxplayer_0.2.7~git20130615~d87aa60a_armhf.deb
-   
- 
  
 +----