Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
image_modifikations [2015/10/18 14:02] admin [Disable the Camera LED] |
image_modifikations [2016/01/28 16:42] admin [Arduino] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ---- | + | ===== Embedded Artist Image Modifications |
- | **Embedded Artist Image Modifications** | + | |
- | ---- | + | |
- | These modifications work with the Raspberry Pi B+, too. | + | These modifications work with the Raspberry Pi B and B+. |
- | Download and burn the Raspbian Wheezy 2014-09-09 Image.\\ | + | Download and burn the Raspbian Wheezy 2014-09-09 Image:\\ |
- | [[http:// | + | [[https:// |
Boot you Rasperry Pi and log in...\\ | Boot you Rasperry Pi and log in...\\ | ||
- | user: Pi\\ | + | user: pi\\ |
pass: raspberry\\ | pass: raspberry\\ | ||
... and make an update:\\ | ... and make an update:\\ | ||
$ sudo apt-get update | $ sudo apt-get update | ||
- | \\ | + | $ sudo apt-get upgrade |
---- | ---- | ||
- | ==== Change name and password | + | ==== Name and Password |
+ | Change the name and the password. | ||
\\ | \\ | ||
[[http:// | [[http:// | ||
Line 36: | Line 35: | ||
$ passwd | $ passwd | ||
- | The passwd command allows you to change your password, you will be prompted for your old password, then you new password twice. The password is " | + | The passwd command allows you to change your password, you will be prompted for your old password, then you new password twice. |
4. Reboot: | 4. Reboot: | ||
$ sudo reboot | $ sudo reboot | ||
- | \\ | ||
---- | ---- | ||
- | ==== Install Scrips | + | ==== Script |
Install the Shutdown/ | Install the Shutdown/ | ||
Line 68: | Line 66: | ||
write before exit 0: | write before exit 0: | ||
# run reset and shutdown script | # run reset and shutdown script | ||
- | | + | |
/ | / | ||
- | | + | # start blinking |
+ | printf "start blinking | ||
/ | / | ||
Line 81: | Line 80: | ||
---- | ---- | ||
- | ==== Install | + | ==== Arduino ==== |
Install the Arduino IDE and the Paper-Duino-Pi modifications. | Install the Arduino IDE and the Paper-Duino-Pi modifications. | ||
Line 89: | Line 88: | ||
2. For the modification of the GPIO Pin and the Avrdude, the easiest way is to download the setup for the AlaMode board: | 2. For the modification of the GPIO Pin and the Avrdude, the easiest way is to download the setup for the AlaMode board: | ||
$ wget http:// | $ wget http:// | ||
- | < | + | < |
unpack it, | unpack it, | ||
- | $ sudo tar xf alamode-setup.tar.gz | + | $ sudo tar xf paper-duino-pi-setup.tar.gz |
and run the setup. | and run the setup. | ||
- | $ cd alamode-setup | + | $ cd paper-duino-pi-setup |
$ sudo ./setup | $ sudo ./setup | ||
That will install a new version of the avrdude and will also do some Linux modifications (one for the alamode board). | That will install a new version of the avrdude and will also do some Linux modifications (one for the alamode board). | ||
Line 119: | Line 118: | ||
---- | ---- | ||
- | ==== Install | + | ==== PD-extended ==== |
1. To install pd-extended run the following command in your terminal: | 1. To install pd-extended run the following command in your terminal: | ||
Line 154: | Line 153: | ||
---- | ---- | ||
- | ==== Enable | + | ==== Sound on Jack ==== |
+ | Enable the Sound on Jack. | ||
$ sudo modprobe snd_bcm2835 | $ sudo modprobe snd_bcm2835 | ||
$ sudo amixer cset numid=3 1 | $ sudo amixer cset numid=3 1 | ||
+ | or change in | ||
+ | $ sudo raspi-config | ||
+ | Advanced Options/ | ||
---- | ---- | ||
==== Stop blanking ==== | ==== Stop blanking ==== | ||
Line 207: | Line 210: | ||
---- | ---- | ||
- | ==== The SSH connection | + | ==== SSH ==== |
Set the SSH connection and the IP address. | Set the SSH connection and the IP address. | ||
Line 237: | Line 240: | ||
---- | ---- | ||
- | ==== FAT32 partition | + | ==== FAT32 Partition |
With G-Part make a fat32 partition on the SD Card, named " | With G-Part make a fat32 partition on the SD Card, named " | ||
Line 250: | Line 253: | ||
---- | ---- | ||
- | ==== Disable the Camera LED ==== | + | ==== Camera LED ==== |
+ | Disable the Camera LED. | ||
$ sudo nano / | $ sudo nano / | ||
edit: | edit: | ||
disable_camera_led=1 | disable_camera_led=1 | ||
- | + | ---- | |
- | ==== Downgrade the omxplayer | + | ==== Omxplayer |
To prevent the OMXPlayer to show the time and " | To prevent the OMXPlayer to show the time and " | ||
$ sudo apt-get autoremove omxplayer | $ sudo apt-get autoremove omxplayer | ||
Line 263: | Line 267: | ||
$ sudo dpkg -i omxplayer_0.2.7~git20130615~d87aa60a_armhf.deb | $ sudo dpkg -i omxplayer_0.2.7~git20130615~d87aa60a_armhf.deb | ||
$ rm omxplayer_0.2.7~git20130615~d87aa60a_armhf.deb | $ rm omxplayer_0.2.7~git20130615~d87aa60a_armhf.deb | ||
- | | ||
- | |||
+ | ---- |